User Tag List

Results 1 to 7 of 7

Thread: Dropout ID help

  1. #1
    Join Date
    Jul 2008
    Location
    Rochester, NY
    Posts
    985
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Dropout ID help

    I went through my box of rear dropouts today and among the many I found these two sets which I sort of don't/do remember buying quite a few years ago. I don't remember who made them or where from I might have gotten them. Does anyone here recognize them? AndyID Dropouts 3.jpgID Dropouts 2.jpgID Dropouts 1.jpg
    Andy Stewart
    10%

  2. #2
    Join Date
    Aug 2008
    Location
    Flagstaff, Arizona
    Posts
    11,156
    Post Thanks / Like
    Mentioned
    11 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Dropout ID help

    Quote Originally Posted by Andrew R Stewart View Post
    I went through my box of rear dropouts today and among the many I found these two sets which I sort of don't/do remember buying quite a few years ago. I don't remember who made them or where from I might have gotten them. Does anyone here recognize them? AndyID Dropouts 3.jpgID Dropouts 2.jpgID Dropouts 1.jpg
    I dunno, but I really like the look of them!

    - Garro.
    Steve Garro, Coconino Cycles.
    Frames & Bicycles built to measure and Custom wheels
    Hecho en Flagstaff, Arizona desde 2003
    www.coconinocycles.com
    www.coconinocycles.blogspot.com

  3. #3
    Join Date
    Jan 2010
    Location
    Olympia, WA
    Posts
    6
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Dropout ID help

    The eyeletted ones remind me of some Kirk Pacenti did. I don't remember a non-eyeletted version...
    Corey Thompson
    Olympia, WA

  4. #4
    Join Date
    Aug 2009
    Location
    Seattle WA USA
    Posts
    21
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Dropout ID help

    I'm about 80% sure they're Mitch Pryor's design. I doubt he CNC'd them himself, probably contracted that out.
    Mark Bulgier
    Seattle

  5. #5
    Join Date
    Jan 2010
    Location
    Olympia, WA
    Posts
    6
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Dropout ID help

    I used a lot of Mitch's- they had similar windows, but were joined at the chainstay side, not the seatstay side, and I don't think he offered them without eyelets.

    Here's an image Kirk sent me in September 2009 when he was getting ready to make them. I used one set when they came out.
    road_rear.jpg
    Corey Thompson
    Olympia, WA

  6. #6
    Join Date
    Aug 2009
    Location
    Seattle WA USA
    Posts
    21
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Dropout ID help

    Yeah that looks likely, but still not 100%. On Andy's, the "land" for the fender eyelet is connected to the one for the axle by an isthmus. You could say the eyelet is a peninsula not an island? (OK no one would say that...)

    Whether Mitch had his own made or bought them from someone (Kirk?), this one on his Flickr seems to have a family resemblance, including the isthmus.

    Ah nevermind, here's a good close-up of the windowed MAP dropouts, and they don't have the isthmus, so Mitch went through different styles I guess. Probably Kirk did too.

    Mitch's also have the tab to go up inside the stay, and Andy's mystery drops don't have the tabs. So I hereby retract my statement that Andy's are MAP!

    I do like a good mystery though.
    Mark Bulgier
    Seattle

  7. #7
    Join Date
    Aug 2008
    Location
    Flagstaff, Arizona
    Posts
    11,156
    Post Thanks / Like
    Mentioned
    11 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Dropout ID help

    Quote Originally Posted by bulgie View Post
    You could say the eyelet is a peninsula not an island? (OK no one would say that...)

    .
    "No man is a peninsula!!!!!"


    - My drunken friend


    - Garro.


    370289911_654259783145736_5776326716819782961_n.jpg
    Steve Garro, Coconino Cycles.
    Frames & Bicycles built to measure and Custom wheels
    Hecho en Flagstaff, Arizona desde 2003
    www.coconinocycles.com
    www.coconinocycles.blogspot.com

Similar Threads

  1. UFP 8 Dropout?
    By Jacob_Curtis in forum The Frame Forum@VSalon
    Replies: 5
    Last Post: 06-04-2013, 07:47 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •