User Tag List

Results 1 to 7 of 7

Thread: Tap tools

  1. #1
    Join Date
    Jul 2019
    Location
    Falls Church, VA
    Posts
    19
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Tap tools

    Didn't see this in a search, so perhaps worth a new post. A first frame-related question.

    Looking for a recommendation for a specific tap: I need to drill and thread a hole in the bottom bracket to mount a cable guide. Anyone got recommendations on what tools they use for the job? Drill bit size and thread metrics?

    Thanks!
    -Corey

  2. #2
    Join Date
    Jul 2008
    Location
    Los Angeles, California, United States
    Posts
    3,743
    Post Thanks / Like
    Mentioned
    3 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Tap tools

    IIRC they're M5 8mm or 10mm length.

    M5 = 4.2mm drill bit (~halfway between 5/32 and 11/64)
    elysian
    Tom Tolhurst

  3. #3
    Join Date
    Jul 2019
    Location
    Falls Church, VA
    Posts
    19
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Tap tools

    Thanks for the input! It's not something I'll use often, but always welcome an excuse to buy new tools.
    Corey Bennett - Falls Church, VA - INSTA

  4. #4
    Join Date
    Feb 2013
    Location
    London, UK
    Posts
    4,810
    Post Thanks / Like
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Tap tools

    An M5 tap is pretty much essential for any mechanic, the vast majority of sundries & threaded bosses will be M5.

    In case you didn't know, the size of the hole to be tapped makes for the amount of thread engagement. The smaller the hole, the more engagement the thread will have, but also the chances of breaking the tap will increase. It depends a lot on the material you are going to drill & tap through.
    For an M5 thread on steel, a 4.2mm drill bit ought to give about 80% of thread engagement, which is overkill, and you're very likely to overheat the tap and break it.
    An average 70-75% of thread engagement is the best compromise, and a lot easier to work with, since you will have to drill 4.40-4.35mm.

    Now, a BB cable guide will get very little stress, so don't need to go mad, but since you're buying the tools just do it right in the first place: get yourself two or three sizes of drill bits per every thread size you're going to work with, and keep those drill bits aside and use them only for drilling holes to be tapped.
    For M3x0.50: 2.70 for 60%, 2.62 for 70%
    For M4x0.70: 3.55mm for 60%, 3.45mm for 75%
    For M5x0.80: 4.45mm for 65%, 4.35mm for 75%
    For M6x1.0: 5.30 for 65%, 5.20 for 75%
    For M8x1.0: 7.30 for 65%, 7.20 for 75%
    Andrea "Gattonero" Cattolico, head mechanic @Condor Cycles London


    "Caron, non ti crucciare:
    vuolsi così colà dove si puote
    ciò che si vuole, e più non dimandare"

  5. #5
    Join Date
    Jul 2008
    Location
    Rochester, NY
    Posts
    983
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Tap tools

    There are many tap drill charts available for the viewing on line. I generally use a #19 bit for a 5x.8 thread pilot. Andy
    Andy Stewart
    10%

  6. #6
    Join Date
    Feb 2013
    Location
    London, UK
    Posts
    4,810
    Post Thanks / Like
    Mentioned
    5 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Tap tools

    Now this is exaggerated, but it shows what happens when the size of a tap cannot cope with the ID that's dealing with.
    Taps do not just "cut" a thread, they actually extrude the crests of the thread (and this is the reason why you cannot put back in the formed thread the pilot drill bit you've used!) so it is important to choose the size of the drill bit according to the material: if the tap is getting too much resistance it will overheat and snap.
    this was easy to get out, but an M4 or worst an M3 cracked in a dropout are a real pain to remove.

    Long story short is: pratice on a similar piece of steel (material and thickness) before you actually go and tap the frame

    Andrea "Gattonero" Cattolico, head mechanic @Condor Cycles London


    "Caron, non ti crucciare:
    vuolsi così colà dove si puote
    ciò che si vuole, e più non dimandare"

  7. #7
    Join Date
    Dec 2009
    Location
    BendOR
    Posts
    2,183
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Tap tools

    This has been my go to tap chart for general purpose stuff for years. The minor diameter should change based on the material and this chart calls that out. You'll have to look elsewhere for a few things like Acme threads or when using form taps but you're probably not going down that road at home.

    https://littlemachineshop.com/images...DrillSizes.pdf

    This video has a lot of good info about tap selection in it. It's intended for automated tapping but it's largely the same. Just use a good cutting oil when tapping by hand. Rapid Tap is good all around choice and easy to come by.

    https://www.haascnc.com/video/tipoft...ruzgooa9k.html

    We use a lot of Guhring and OSG taps and drills for production. They're a lot better than the general purpose stuff you'll find at the hardware store, like that tap of Anrdeas that's in two pieces. They aren't that much more expensive either.

Similar Threads

  1. Replies: 13
    Last Post: 04-23-2016, 07:18 AM
  2. cobra tools are no more :( ! time to design new tools !
    By NBC in forum The Frame Forum@VSalon
    Replies: 12
    Last Post: 07-16-2014, 04:17 PM

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •