User Tag List

Page 1 of 2 12 LastLast
Results 1 to 20 of 25

Thread: Photos of main tube mitering fixtures for bridgeport

  1. #1
    Join Date
    Jun 2009
    Posts
    65
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Photos of main tube mitering fixtures for bridgeport

    Hello Gents,

    What worked? What did not? Not trying to reinvent the wheel over here. Would love to see what you came up with!

    THX

  2. #2
    Join Date
    May 2008
    Location
    Better to be ruined than to be silent atmo.
    Posts
    22,127
    Post Thanks / Like
    Mentioned
    24 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    except for a brief period in the late 80s/mid 90s when i went machine crazy, all of my pipes are hand mitered
    using either a 10" or 12" half-round bastard cut file. i budget 35-50 seconds per cut. after that, it's just me
    wasting time admiring the fit atmo.
    Attached Images Attached Images

  3. #3
    Join Date
    May 2008
    Location
    Better to be ruined than to be silent atmo.
    Posts
    22,127
    Post Thanks / Like
    Mentioned
    24 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    ps - asshat me. i just now saw the end of the thread title "...fixtures for bridgeport".
    i missed them when i was replying.

  4. #4
    Join Date
    May 2008
    Posts
    7,157
    Post Thanks / Like
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    You used to be a fixture in CT. That's bigger than Bridgeport.

  5. #5
    Join Date
    Feb 2009
    Location
    State College, PA
    Posts
    5,605
    Post Thanks / Like
    Mentioned
    2 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Anvil, Sputnik and Brigheli all have mill based set ups. Lots of folks have great success with tube blocks and mill vices or three jaw vices.

  6. #6
    Join Date
    Jan 2010
    Posts
    23
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    I'm working on one right now - initially I'll put it in the vise, but I'll modify it eventually to bolt right to the table, keyed to the T-slot. It'll have an interchangeable tube holder section (it's based on a Bosch T-slot extrusion I had a bunch of), so I can use it for seat stays as well (it goes to 55 degrees) and possibly chainstays; haven''t figured that part out yet. Not shown is the part that times the cuts on each end to each other; it's not quite as simple as I'd like yet. The V-blocks and the big plate aren't either, but they're made, and no way am I redoing those.

    Of course the file is faster (if you're good at it), but it's fun to design new tools! I should be out in the garage right now...

    Andrew





    Edit - I remembered this one from a machinist's forum I visit. Simple and relatively cheap, but no means of aligning the cuts.

    Last edited by Andrew Drummond; 04-17-2011 at 02:15 AM. Reason: added photo

  7. #7
    Join Date
    Dec 2008
    Posts
    172
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    If you're low volume and work in standard diameter tubes as I do I really don't think you need anything more than tube blocks. The blocks Paragon make are excellent. A dedicated fixture makes sense if you're doing larger volumes and especially if you have a dedicated machine.
    -Martin

  8. #8
    Join Date
    Sep 2008
    Location
    Bozeman MT
    Posts
    308
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Here is mine. V-blocks in a vise on a rotary table with my mill head turned 90 degrees. I only use this machine for maintubes and chainstays. That bar behind the vise holds a dummy tube that I use to keep the cuts in phase. I like it because I can setup a cut in very little time and walk away and reply to email while it runs.
    Attached Images Attached Images
    Carl Strong
    Strong Frames Inc.
    www.strongframes.com

  9. #9
    Join Date
    Feb 2009
    Location
    West of Portland Oregon
    Posts
    2,264
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Carl, how often do you tip the head of your mill back to vertical? and or deal with lubrication?

    Thats pretty much how I do it but I've been in the habit of using two paragon blocks on each tube, set on the flat table and then just rotated a quarter turn in the vise to phase the miters.

  10. #10
    Join Date
    Sep 2008
    Location
    Bozeman MT
    Posts
    308
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Quote Originally Posted by bellman View Post
    Carl, how often do you tip the head of your mill back to vertical? and or deal with lubrication?
    The machine is dedicated to this process so I never tip the head back but I do make sure it stays lubricated because of it's orientation.
    Carl Strong
    Strong Frames Inc.
    www.strongframes.com

  11. #11
    Join Date
    Sep 2010
    Location
    Birdsboro Pa.
    Posts
    6
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    This is my approach. I've also made a set of mandrels to insure the TT and DT are in phase . It was alot of work to make all this stuff, but i use it for every frame.

    Sparks

    Cedarboro cycles

    www.cedarborocycles.com
    Attached Images Attached Images

  12. #12
    Join Date
    Jun 2009
    Posts
    65
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    thanks for all these ideas everyone. I found a nice bridgeport in a storage unit at the warehouse. I shot the owner an offer of 750.00 and 10 day inspection period. He accepted. I've resisted tooling up and have no machines at the moment. Currently all miters are cut by hand.

    How much should one expect to spend on a rotary table? @Andy in post #6 i notice the jaws in the vice. Many non-traditional shaped tubes will be cut, these jaws will be helpful. where can these jaws be found?

    I'm a tight wad and worried about all of the hidden costs associated with the bridgeport. tooling, collets, phase converter... yadda yadda.

    Any links to used equipment pages? If you were to walk into my shop you'd understand shiny isn't needed. functional is required! ;)

  13. #13
    Join Date
    Aug 2008
    Location
    Flagstaff, Arizona
    Posts
    11,145
    Post Thanks / Like
    Mentioned
    11 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    My set-up - Garro.
    Attached Images Attached Images
    Steve Garro, Coconino Cycles.
    Frames & Bicycles built to measure and Custom wheels
    Hecho en Flagstaff, Arizona desde 2003
    www.coconinocycles.com
    www.coconinocycles.blogspot.com

  14. #14
    Join Date
    Jan 2010
    Posts
    23
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    ... i notice the jaws in the vice. Many non-traditional shaped tubes will be cut, these jaws will be helpful. where can these jaws be found?
    Not found, as far as I know, but made - on your new Bridgeport! They appear to have been inspired by those on Anvil's main tube mitering jig.

    Andrew

  15. #15
    Join Date
    Jun 2008
    Location
    Ballston Spa, N.Y. U.S.A.
    Posts
    168
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Quote Originally Posted by Carl S View Post
    Here is mine. V-blocks in a vise on a rotary table with my mill head turned 90 degrees. I only use this machine for maintubes and chainstays. That bar behind the vise holds a dummy tube that I use to keep the cuts in phase. I like it because I can setup a cut in very little time and walk away and reply to email while it runs.
    Pretty cool.
    I suppose once into the table is enough to make one think...
    Plus the boss hears the machine running when he calls...
    Nice big arbor diameter, too.

  16. #16
    Join Date
    Sep 2010
    Location
    Waterloo Ontario
    Posts
    78
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    I switched to abrasive belts when I did my first S3 tubed bike. I didn't like the way hole saws worked on the thin tubing. Turns out the belt method also works really well for carbon. I can make whatever mandrel size I need on the lathe too. The tube holding does not have to be too rigid, the load on the tubes is quite low.



    back40 bicycleworks

  17. #17
    Join Date
    May 2009
    Location
    I AM FROM BENDOR
    Posts
    262
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Mine is freaking bomber. I use a digital angle finder to find the angle, um digitally.

  18. #18
    Join Date
    Aug 2008
    Location
    Boston, MA
    Posts
    196
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    This is my new fixture. It is based on the center of the rotary table and the centering vise has V block jaws. It makes main tube mitering easy.

    IMG_20110420_181902.jpg

  19. #19
    Join Date
    Jun 2008
    Location
    Sutton, MA USA
    Posts
    4,548
    Post Thanks / Like
    Mentioned
    1 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Here's my system. I take the SS fixture out when I'm not using it. It takes just a couple of minutes to go between the two.

    Mike Zanconato
    Web
    | Instagram | Twitter | Facebook | Flickr | Tumblr

  20. #20
    Join Date
    Apr 2010
    Posts
    12
    Post Thanks / Like
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Default Re: Photos of main tube mitering fixtures for bridgeport

    Hi -- Nice work! I'm a fan of abrasive mitering as well. Mind if I ask a few questions?
    Do you hog out material manually (shears/nibbler/bandsaw) prior, or do you do the entire miter w/ the abrasive?
    What do you like for grit/abrasive?
    Do you use dif grit/abrasive for carbon than for steel?
    Any heating issues w/ resin in the carbon?
    THx, JF

Page 1 of 2 12 LastLast

Similar Threads

  1. guide tube for through top tube brake cable , anyone order from McMaster
    By EricKeller in forum The Frame Forum@VSalon
    Replies: 14
    Last Post: 10-28-2010, 07:51 PM

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •