Page 24 of 123 FirstFirst ... 141516171819202122232425262728293031323334 ... LastLast
Threads 461 to 480 of 2442

Forum: The Frame Forum@VSalon

Sage advice and opinions from experienced tradespeople.

  1. Slightly bike related: resistance welding Ti

    Started by Mark Kelly, 05-24-2017
    alloy, electrical, resistance, stress, welding
    • Replies: 0
    • Views: 1,317
    Mark Kelly
    05-24-2017 Go to last post

  2. Anyone selling Victor J28 Torch or similar?

    Started by abeship, 05-22-2017
    j28, laying, practice, thought, thread
    • Replies: 2
    • Views: 2,348
    Andrew R Stewart
    05-23-2017 Go to last post

  3. Torch Handle size comparison

    Started by cicli polito, 05-23-2017
    day, harris, light, smith, victor 1 Attachment(s)
    • Replies: 0
    • Views: 1,293
    cicli polito
    05-23-2017 Go to last post

  4. I brazed a fork crown to the non-reinforced end of a steerer tube - advice?

    Started by Astrapower, 05-09-2017
    crown, end, fork, steerer, tube
    • Replies: 10
    • Views: 4,785
    jclay
    05-16-2017 Go to last post

  5. Rear road bike disc mounts

    Started by Boedie, 05-10-2017
    bike, disc, mount, mounts, rear
    • Replies: 4
    • Views: 3,552
    Boedie
    05-12-2017 Go to last post

  6. Lightbulb Aluminum Framebuilding Tips!

    Started by juggaloslaya, 05-11-2017
    aluminum, start, tips, tricks, welding
    • Replies: 0
    • Views: 1,771
    juggaloslaya
    05-11-2017 Go to last post

  7. Kavik dropout inserts needed

    Started by shand, 05-10-2017
    asap, dropouts, hoping, inserts, kavik
    • Replies: 0
    • Views: 1,180
    shand
    05-10-2017 Go to last post

  8. welding ti, machine setting and filler rod size

    Started by michäel2, 04-10-2017
    amp, filler, rod, setting, welding 4 Attachment(s)
    • Replies: 10
    • Views: 4,853
    VertigoCycles
    04-25-2017 Go to last post

  9. WTB - Anvil Tube Bender

    Started by Larry, 04-24-2017
    anymore, benders, gmail, hit, larry
    • Replies: 0
    • Views: 1,545
    Larry
    04-24-2017 Go to last post

  10. Full suspension.....pivots?

    Started by Will Neide, 03-27-2017
    main, pivot, pivots, simple, single 4 Attachment(s)
    • Replies: 7
    • Views: 3,034
    MDEnvEngr
    04-24-2017 Go to last post

  11. Optimum dropout for Belt Drive

    Started by jaybeeboston, 04-17-2017
    belt, belt drive, drive, dropouts, good
    • Replies: 8
    • Views: 3,113
    Rody
    04-20-2017 Go to last post

  12. Advice and experience building your own alignment table

    Started by Weldingfellow, 04-12-2017
    advice, alignment, holes, table, wide
    • Replies: 6
    • Views: 2,523
    Weldingfellow
    04-13-2017 Go to last post

  13. Columbus Max Tubing

    Started by SaltAirCX, 04-06-2017
    columbus, columbus max, max, pipes, set
    • Replies: 3
    • Views: 2,466
    Pi Guy
    04-07-2017 Go to last post

  14. Thick wall tubes?

    Started by JGabriel, 04-03-2017
    frame, frames, oversized, touring, tubes
    • Replies: 3
    • Views: 2,395
    JGabriel
    04-04-2017 Go to last post

  15. Flat mount disc brakes and single speed

    Started by hurricanejosh, 03-16-2017
    brakes, disc, flat, mount, vertical
    • Replies: 10
    • Views: 3,822
    Ben Hudson
    04-01-2017 Go to last post

  16. Hooded sliding dropouts and fillet brazing

    Started by Furry, 03-21-2017
    fillet, fillet brazing, frame, hooded, hooded dropout 1 Attachment(s)
    • Replies: 3
    • Views: 3,336
    progetto
    03-30-2017 Go to last post

  17. Framebuilder Flow Chart and their Beginnings

    Started by Andrew R Stewart, 03-25-2017
    beginnings, builders, nodes, remember, thread
    • Replies: 5
    • Views: 3,857
    fortyfour
    03-26-2017 Go to last post

  18. Tin-Silver for stainless dropouts

    Started by Koldun, 03-21-2017
    alloy, s45, stainless, strong, tin-silver
    • Replies: 0
    • Views: 1,813
    Koldun
    03-21-2017 Go to last post

  19. A report on using a BernzOmatic mapp/oxygen unit for brazing a lug

    Started by Doug Fattic, 03-09-2017
    flame, lug, make, oxygen, unit
    • Replies: 2
    • Views: 2,814
    Ben Hudson
    03-17-2017 Go to last post

  20. Ye ol' chop and slot~~

    Started by drietz, 03-06-2017
    question, seat, top, tube, weld
    • Replies: 6
    • Views: 3,805
    drietz
    03-11-2017 Go to last post
Page 24 of 123 FirstFirst ... 141516171819202122232425262728293031323334 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 100 replies or 200 views
Hot thread with unread posts
More than 100 replies or 200 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules