Page 13 of 124 FirstFirst ... 34567891011121314151617181920212223 ... LastLast
Threads 241 to 260 of 2461

Forum: The Frame Forum@VSalon

Sage advice and opinions from experienced tradespeople.

  1. Notching tubes on a mill + Digital Angle Finder/Inclinometer suggestion

    Started by false_aesthetic, 10-30-2019
    block, cut, inclinometer, make, tube 1 Attachment(s)
    • Replies: 6
    • Views: 6,686
    Jamie Medeiros
    11-05-2019 Go to last post

  2. Bi-Oval Downtube

    Started by FullTiltBoogie, 11-02-2019
    bi-oval, find, howdy, stock, yall
    • Replies: 1
    • Views: 4,419
    progetto
    11-02-2019 Go to last post

  3. Tubing choice for a 28.6 downtube on a lugged randonneur frame

    Started by Alex H-L, 10-17-2019
    28.6 downtube, frame, lugged, randonneur, tubing
    • Replies: 4
    • Views: 5,502
    jon_norstog
    11-01-2019 Go to last post

  4. Indenting 853 c-s

    Started by Sixren, 10-23-2019
    /patrik, clerance, indents, make, tire
    • Replies: 5
    • Views: 5,417
    Amaro Bikes
    10-28-2019 Go to last post

  5. Looking for a New England Powder Coater comfortable/proficient with bicycles.

    Started by Thicket Workshop, 10-21-2019
    coater, england, good, powder, results
    • Replies: 0
    • Views: 4,293
    Thicket Workshop
    10-21-2019 Go to last post

  6. Kevlar Brazing Hose Question

    Started by rstankus, 10-18-2019
    connection, hose, kevlar, set, years
    • Replies: 1
    • Views: 4,425
    Eric Estlund
    10-19-2019 Go to last post

  7. Vent Holes and Rear Triangle Alignment

    Started by JD Reich, 10-17-2019
    alignment, chainstays, seatstays, tacking, wheel
    • Replies: 3
    • Views: 3,699
    JD Reich
    10-18-2019 Go to last post

  8. Seatstay mitre angle

    Started by ltwiens38, 10-08-2019
    adjust, angle, degrees, fixture, mill
    • Replies: 3
    • Views: 4,464
    crumpton
    10-17-2019 Go to last post

  9. Welding respirator

    Started by Jonathan, 03-14-2013
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 21
    • Views: 9,683
    jclay
    10-14-2019 Go to last post

  10. Head tube+stack height vs steerer length

    Started by mmoore, 10-10-2019
    fork, question, steerer, stem, top
    • Replies: 3
    • Views: 3,643
    mmoore
    10-11-2019 Go to last post

  11. CX Front Derailleur Pulley - Where to get?

    Started by jclay, 10-07-2019
    der, front, pull, pulley, top
    • Replies: 4
    • Views: 4,770
    EnginCycles
    10-08-2019 Go to last post

  12. Anvil Fixtures? What's the scoop?

    Started by Dancingbear, 10-08-2019
    anvil, building, exception, frame, site
    • Replies: 1
    • Views: 4,471
    Dancingbear
    10-08-2019 Go to last post

  13. Noodle-like XL frame problem

    Started by ltwiens38, 03-24-2019
    cranks, frame, long, problem, works 1 Attachment(s)
    • Replies: 8
    • Views: 11,760
    ltwiens38
    10-08-2019 Go to last post

  14. Unicrown blades?

    Started by steve garro, 02-09-2014
    1 Attachment(s)
    • Replies: 5
    • Views: 5,483
    Amaro Bikes
    10-03-2019 Go to last post

  15. Hole Saw Difficulties

    Started by Russer72, 09-29-2019
    cheers, cut, hole, starrett, thinking
    • Replies: 3
    • Views: 4,699
    Eric Estlund
    09-30-2019 Go to last post

  16. Chain stay internal routing

    Started by Cord, 09-18-2019
    cable, chain, internal, routing, stay 7 Attachment(s)
    • Replies: 14
    • Views: 5,664
    steve garro
    09-25-2019 Go to last post

  17. Using old automotive paint (cans you've had for 15 years)

    Started by jclay, 09-06-2019
    automotive, fine, guys, panel, years 1 Attachment(s)
    • Replies: 3
    • Views: 3,798
    Andrew R Stewart
    09-19-2019 Go to last post

  18. Flat mount rear brake

    Started by jon_norstog, 09-16-2019
    brake, chainstay, flat, mount, rear 3 Attachment(s)
    • Replies: 2
    • Views: 3,730
    jon_norstog
    09-17-2019 Go to last post

  19. Cutter compensation for offset mitering ST notch

    Started by VertigoCycles, 09-17-2019
    mill, miter, seat, tube, tubes
    • Replies: 0
    • Views: 3,316
    VertigoCycles
    09-17-2019 Go to last post

  20. Shimano GRX crank frame clearance docs

    Started by EricKeller, 09-17-2019
    clearance, frame, spent, struck, time
    • Replies: 1
    • Views: 3,005
    EricKeller
    09-17-2019 Go to last post
Page 13 of 124 FirstFirst ... 34567891011121314151617181920212223 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 100 replies or 200 views
Hot thread with unread posts
More than 100 replies or 200 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules